Theatrical sidearms are asked to do a job they were never designed to do. A typical sidearm is made up of a c-clamp and a piece of ½” pipe. When downward pressure is placed on the pipe, it will bend the bolt of...
A Boom Arm consists of a 48mm aluminium tube with a factory fitted weld coupler. TECHNICAL SPECIFICATIONS SWL: 1000mm - 25 Kg Downloads: Data...
A Boom Arm consists of a 48mm aluminium tube with a factory fitted weld coupler. TECHNICAL SPECIFICATIONS SWL: 500mm - 50 Kg Downloads: Data...
A range of steel boom arms. Available with a safety bond anchor point. TECHNICAL SPECIFICATIONS Fits Tubes: 48 - 51mm Centres: 280mm from pipe centre to hole centre...
A ceiling saddle is shaped to bridge any small obstructions. Supplied with a 10mm mounting holes and accepts M12 Bolt/M12 Studding with provision for adjustment. TECHNICAL SPECIFICATIONS Stand Off: 75mm Weight: 0.44 Kg...
The Doughty 90 Degree Fixed Coupler provides a firm fixing between two perpendicular bars. Manufactured from high tensile Aluminium Extrusion. TECHNICAL SPECIFICATIONS SWL: 750 Kg Tube Diameters: 48 to 51mm Width: 50mm Tube...
The Doughty Hanging Clamp is supplied fitted with an Eye nut. This Clamp is ideal for suspending wire hung loads. Manufactured from high tensile Aluminium Extrusion and available in Black or Polished Aluminium. TECHNICAL...
The Doughty Swivel Coupler provides a firm fixing between adjacent bars whilst allowing 360 degrees of movement. Manufactured from high tensile Aluminium Extrusion. TECHNICAL SPECIFICATIONS SWL: 750 Kg Tube Diameters: 48 to...
Gravlock couplers are used to attach 48mm barrel to a girder / beam at 90 degrees. Suitable for flanges up to 45mm thick. It is important to note these couplers must be used in pairs as supplied. TECHNICAL...
Pipe to wall brackets are available in two sizes providing a stand off of 100mm and 300mm. Manufactured in mild steel with a bright zinc plate finish.
A 90 degree elbow joint between two tubes. TECHNICAL SPECIFICATIONS Tube Diameter: 48mm Weight: 0.87 Kg Downloads: Data...
A Termination flange to be used on structures where a positional fixing only is required. 8mm mounting holes. This fitting is not recommended for use as a base plate for Guard railing, see T13200. TECHNICAL...
A 90 degree connection between two tubes. This Pipeclamp can be used to join two tubes in the top of the twin grub screw long tee. TECHNICAL SPECIFICATIONS Tube Diameter: 48mm Weight: 1.04 Kg...
A structural base plate for all aspects of vertical tube support. The holes in the base plate are large enough to enable the use of mechanical or chemical anchor fixings. TECHNICAL SPECIFICATIONS Mounting Holes: 14mm...
A pressed steel coupler used to join two tubes at 90 degrees to each other. Finished in yellow passivate. TECHNICAL SPECIFICATIONS Tube Diameter: 48mm Material: Pressed Steel Weight: 1.02 Kg...
An internal pipe to pipe joiner. Finished in yellow passivate. TECHNICAL SPECIFICATIONS Tube Diameter: 48 x 5mm Weight: 0.85 Kg
A heavy duty one piece tube joiner used to join 48mm tubes externally. Finished in Bright Zinc Plate. TECHNICAL SPECIFICATIONS Tube Diameter: 48mm Weight: 2.64 Kg Downloads: Data...
The OPTI Trilite 200 Panel Coupler is used to fix solid panels to OPTI Trilite 2 inch tubes or truss.
The OPTI Trilite 200 Half Coupler with Lifting Eye is used to suspend OPTI Trilite 2 inch tubes or truss rigs with wires from ceilings or other solid structures.
The OPTI Trilite 200 Steel Saddle Clamp creates a strong, permanent connection to secure OPTI Trilite 200 Truss to walls, floors, ceilings or other flat surfaces.
A universal clamp to suit a 48mm tube. Shaped to captivate a bolt head or nut. TECHNICAL SPECIFICATIONS SWL: 48mm - 200Kg
Back to Top