Rigging

Factory fitted with a snap-in pin for use in conjunction with the G1160 Supaclamp or similar accessories. The clamp plates are designed to accept 16, 12, 10 and 6mm diameter pole/arms. This item is an accessory for the...

A steel snap in Offset arm with two 16mm lighting pins designed to fit the Supaclamp. This item is an accessory for the Doughty Super Clamp Technical Specification Overview Spigot Diameter 2 x Ø15...

A stainless steel snap in 150mm extension used to join two supaclamps together. This item is an accessory for the Doughty Super Clamp Technical Specification Overview WLL Not...

A stainless steel Snap In Swivel Joiner used to join two supaclamps together. This item is an accessory for the Doughty Super Clamp Technical Specification Overview WLL Not Rated Finish Stainless...

A range of stainless steel snap in studs designed to fit the Supaclamp. Available in either M12 x 30 or M10 x 25. This item is an accessory for the Doughty Super Clamp Technical...

A brass double ended snap in 16mm spigot with a ¼” and 3/8″ UNC thread. This spigot features two 16mm shanks to be used with 16mm receivers and a ¼” UNC thread one end and a 3/8″ UNC...

G1180: A brass snap in 16mm spigot with a 3/8″ UNC thread. This spigot features a 16mm shank to be used with 16mm receivers and a 3/8″ UNC thread as used with larger cameras and accessories. G1181: A brass snap...

A brass snap in socket with an M10 thread. This spigot features a hex head and will freely rotate unless locked with the thumb screw. This item is an accessory for the Doughty Super Clamp Technical...

A brass snap in spigot with ¼” UNC thread as used on most Cameras & accessories. This spigot features a knurled ring to grip whilst tightening, the spigot and accessory is then able to rotate or can be...

An M10 x 25 brass snap in spigot which allows 360 degrees rotation. Supplied with a wing nut this spigot features a knurled ring to grip whilst tightening the wing nut, the spigot and accessory is then able to rotate or can...

A steel snap in 100mm X 100mm Mounting Plate designed to fit the Supaclamp. This item is an accessory for the Doughty Super Clamp Technical Specification Overview WLL Not...

A stainless steel snap in either an M10 or M12 socket designed to fit the Supaclamp. This item is an accessory for the Doughty Super Clamp Technical Specification Overview WLL Not...

A range of stainless steel snap in pins designed to fit the Supaclamp. Available in three sizes. Technical Specification Overview WLL Not Rated Materials Stainless SteelGrade 8.8...

A high tensile extruded aluminium clamp that is suitable for 48mm – 51mm (1.89″ – 2.01″) diameter tubes. Designed to connect two tubes together quickly and safely. Available in polished silver...

A steel pipe to pipe clamp designed to suspend a 48mm diameter tube from another 48mm diameter tube. Available in three sizes. Technical Specification Overview WLL 220Kg Tube Diameter 48mm Clamp...

A high tensile extruded aluminium trigger clamp that is suitable for 48mm to 51mm diameter tubes. Has a WLL of 200Kg and is 30mm wide factory fitted with an Eye Nut. Available in polished silver. Technical...

A galvanised steel fitting designed to provide a cross joint between a vertical and two horizontal tubes. Technical Specification Overview WLL Not Rated Tube...

A galvanised steel fitting, designed to be used as a four way cross that enables the vertical to pass through the centre of the fitting. The four outlets then operate at 90 degrees. The vertical must remain continuous with...

A steel double ended parallel hook clamp available in five sizes. Zinc plated finish. All Hook Clamps are Stamped with a WLL. Technical Specification Overview WLL 40Kg Tube...

A galvanised steel fitting, designed to provide a 90 degree corner with the vertical tube passing through the pipeclamp. Technical Specification Overview WLL Not Rated Tube...

A steel heavy duty hook clamp suitable for 48mm to 51mm diameter tube fitted with a 29mm receiver designed to accept a 28mm spigot and a lynch pin for secondary safety. Zinc plated finish or powder coated black. All Hook...

A steel heavy duty hook clamp suitable for 38mm to 51mm diameter tube complete with a strip to help protect the tube. Powder coated black finish. All Hook Clamps are Stamped with a WLL. Technical...

A steel hook clamp suitable for 48mm to 51mm diameter tube. The industry standard hook clamp designed for suspending luminaires. Zinc plated finish. Technical Specification Overview WLL 40Kg Tube...

An innovative pressure die cast aluminium clamp that is suitable for 38mm to 51mm diameter tubes. It has a WLL of 50Kg and is 30mm wide. Slotted to hold captive an M10 nut or bolt head. Ideal for use with lightweight...

holds down individual cables directly on the chord tube possible to straighten cables by pulling them taut – axial resistance provided by rubber band no change in workflow; continuing easy installation and removal...

Truss clamp SNAP is available in the colours black and silver. Material: Plastic (polyamide) Compatible with all standard 2 inch (48-51mm) Truss FEATURES Cable Routing Holds cables up to a total cross-section...

Theatrical sidearms are asked to do a job they were never designed to do. A typical sidearm is made up of a c-clamp and a piece of ½” pipe. When downward pressure is placed on the pipe, it will bend the bolt of...

Theatrical sidearms are asked to do a job they were never designed to do. A typical sidearm is made up of a c-clamp and a piece of ½” pipe. When downward pressure is placed on the pipe, it will bend the bolt of...